There are many laser engraving machine software, we use type3 as an example.
1, loaded type3
Insert the CD into the CD-ROM drive, open "My Computer", select the CD and double-click it, double-click "TYPE3V4200", double-click "SETUP", double-click "NEXT", double-click "YES",
Double-click "NEXT" continuously, the computer will be installed automatically, you can take a break, click "FINISH", the computer restarts
2, decompression
Open "My Computer", select the CD and double click, double click "TYPE3V4200", double click "crack1", click "APPLY", click "OK", double click "crack2", click "APPLY", click "OK" At this point, the decompression has been completed.
3, change the "post processor"
(1) Go back to the desktop and double-click the type3 icon
(2) Click the plus sign "+" in front of "Join Machine"
(3) Click the plus sign "+" in front of "CNC Machine"
(4) Select "Fanuc16M/Fanuc0M" to make it a green bottom
(5) Click "Join" in the lower right corner
(6) Click on any "confirm"
(7) Click on the "post processor..." on the right
(8) Pull the scroll bar down and change the 6 "9" in Nmax=999999 to 10 "9"
(9) Pull the scroll bar down and change the "p" in HeadpcrSz0=p to uppercase "%"
HeadpcrSz1=G91. G28
HeadpcrSz2=t is equal to the number "="
HeadpcrSz3=M6 is deleted later.
(10) Change "17" in EndpcrSz0=M17 to "05"
(11) Click "Confirm" in the upper right corner
(12) The minimum X: -200.000mm maximum: 200.000mm
Change to: -2000.00mm to: 2000.00mm
Minimum Y: -200.000mm maximum Y: 200.000mm
Change to: -2000.00mm to: 2000.00mm
Minimum: -100.000mm Maximum: 100.000mm
Change to: -50.00mm to: 50.00mm
(13) Click "Confirm"
(14) Click “Exit” (the type3 interface will pop up automatically)
4, change the engraving page and options
Take "SW-1218" as an example (the depth is the same according to your own model)
Press F10, you need to change the following parameters
a. General cancellation steps: 10 to 30
Automatic save: 20 changed to 3
Click on "Sound": remove the tick
b. Display click "Show Emboss": remove the tick
c. Engravable page
The width is changed to "1200mm" (L) left left edge: 0mm
(R) Right edge: 0mm
Height changed to "1800mm" (B) bottom edge: 0mm
(T) top edge: 0mm
The depth is changed to "150mm" top edge: 0mm
Bottom edge: 0mm
d. Calculate the parameters: Click “Manual” to make it selected, and change 0p1 to “2”.
Create a new page, this is the actual countertop of your engraving machine
5, change the "machine work"
(1) Draw a box, enter the CAM module, create a tool path, and enter "machine work"
(2) Click on one of the following locks to open it
(3) Click on "File" to make it selected
(4) Click on “Share” on the right: Click “Curve Line Segmentation” to tick it
Z safety start position: 0.000mm to 1.000mm
Click "confirm"
(5) Click "Confirm", "Execute", close type3, and save.
(6) The first time you open the U00 file, you must open it with Notepad or WordPad.
Laser engraving machine software download and installation operation?
First, corelDRAW9 as a vector step:
1. Outline line----closed curve
method one:
After clicking the "Rectangle Tool" or "Oval Tool" or "Polygon Tool" in the toolbox, hold down the left mouse button in the drawing area to draw the corresponding contour line.
Method Two:
(1) "File" menu / input / select image files in JPG, GIF, BMP, WMF, etc. / click the "Enter" button.
(2) Position the picture in the appropriate position in the drawing area to adjust the picture size. Click anywhere outside the picture area to cancel the picture selection status.
(3) Click the fourth icon of the toolbox to the lower right black triangle, select the “Bez Curve Tool”, draw the outer border multi-point curve, and finally the curve is closed. (Note: not too many points in the curve)
(4) Click to select Toolbox “Shaping Tool”, move the mouse to adjust the line segment, right click mouse / shortcut menu / to curve / hold down the left mouse button to adjust the line.
(Note: When the curve is not well adjusted, move the mouse to adjust the line segment / right click the mouse / shortcut menu / add, add a fixed point, then adjust the curve.)
2, the hole line
After clicking the "Oval Tool" in the toolbox, you need to punch the position in the figure, hold down the left mouse button and drag to draw the hole line. (Note: the hole line cannot be too close to the outline)
3, text
Click to select "Text Tool" in the toolbox, click on the text in the picture, enter the text content, adjust the font and size.
4, other lines in the outline
Toolbox
"Hand-painted tools"----Draw a single line
"Bez Curve Tool"----Draw a closed curve
5, set the line color
Click to select "Dripper Tool" in the toolbox / click "Color docker" / select the color changing line / color selection / click the "outer frame" button.
6, delete the background image
Click on "Select Tool" / Select Picture / Cut
7, save the vector (PLT format file)
Save the vector by clicking the File menu / Output / OK Save Location, File Name, File Type (PLT) / Click the Output button.
Second, the laser cutting operation steps
1. Start the LaserCa laser engraving machine software and enter the working interface.
2, "File" menu / import / select vector file (plt format file) / click the "Open" button
3. Position the vector image in the appropriate position in the black cutting area
4, adjust the vector cut size and the starting cutting position
toolbar:
X, Y - starting cutting position, it is recommended to set to zero
, - the width and height of the actual cutting size
5, select the entire vector, "Edit" menu / all dissolved
6. In the toolbox, click to select "Define Quadrilateral Engraving Area" or "Polygon Engraving Area" to circle the text in the vector.
※Select the entire vector / "Edit" menu / batch copy / set the number of copies and spacing
7, set the two-color board engraving parameters
"Settings" menu / engraving settings / check "Inscription" / Basic settings "Engraving speed" 20000mm / min, "Engraving level" 50% / Advanced settings are not checked "Outer frame cutting" / Click "OK " button.
8, set the two-color plate cutting parameters
"Settings" menu / Cut Settings / Click on the "Cut Speed" and "Cut Level" parameters in a color bar / basic settings / click the "OK" button.
Note:
A, do not cut through the line ---- "cutting speed" 20000mm / min, "cutting energy level" 50%
Cut through the line ------ "cutting speed" 500mm / min, "cutting energy level" 100%
B. The higher the cutting speed, the smaller the cutting force.
9, "Run" menu / run (transfer files to the engraving machine)
10. Auxiliary material board on the engraving machine operation surface
11, adjust the laser head position
12, press the "light setting" button to allow light
13, engraving machine panel / "file" button / selected file / "start" button
14, the end of the cut, press the "back" button
15. Press the “light setting” button again to cancel the light.
16. Take out the work on the engraving machine operation surface
